Concrete Repairs & Grouts
Vetogrout CG513

Free-flowing pre-bagged non-shrink cementitious cable grout

Uses
Grouting of anchor cables in suspended bridges.
Grouting of anchors in post-tensioning cases.
Soil stabilization grouting and micro-grouting.
Cavity infill under foundations and grade slabs.
Fast Download
Technical Information
Product Description

Vetogrout CG513 is a single component cementitious grout composed of blended cement, special additives, and fillers to enable fluid consistency and smooth, free flow of grout in demanding anchor post-tensioning applications. Once mixed with the designated amount of water, the product will form a fluid grout that is either pourable or pumpable through small openings to long distances using Saveto recommended grout pumping equipment.

Advantages
  • Free flow characteristics.
  • Non-Shrink with high adhesion.
  • Low coefficient of thermal expansion.
  • Hydrogen and chloride free.
  • The tropical formulation is suitable for MENA conditions.
  • High ultimate and early strength.
  • Suitable for grouting post-tensioned cables and anchors.
  • Contains migratory corrosion inhibitors to protect stressed steel cables and anchors.
COMPLIANCE STANDARD
  • ASTM C938-10
  • ASTM C1741 (Testing of post-tensioning tendon grout)
  • EN 1992
  • EN 447
Packaging & Coverage

Vetogrout CG513 supplied in 25Kg Bag.

Yield: ≈18.5 Liters.

Stated consumption data are for general guidance. Actual consumption depends on the nature of substrate, method of application, and wastage.

Shelf Life & Storage

The original sealed bag of Vetogrout CG513 has a shelf life of 12 months, provided it is stored clear of ground in a dry and shaded place.

Application Information
Instructions for use

Mixing

Measure and pour 7.5 to 8.25 liters of clean water into a suitable sized bucket, then slowly add the powder of one full bag of 25kg size to the bucket while mixing using a slow speed mixer fitted with a suitable mixing paddle. Continue mixing for an additional 3 minutes until achieving a uniform lump-free consistency. 

Allow the grout to mature for 1 minute before pouring; for larger quantities, it is recommended to use a pan forced action mixer, do not use free fall mixers.

Placing

Place Vetogrout CG513 by pouring into the designated application area continuously and not allowing air pockets to develop. The pouring should be within a maximum of 20 minutes after mixing.

Where grout pumps are used for duct grouting, it is recommended to place the hose as deep as possible into the duct, start the pumping process, and then slowly retract the hose, ensuring that pumped material is pushing the air out of the duct.

Cleaning

Remove Vetogrout CG513 from tools and equipment with Vetonit Solvent XX400 immediately after use. Remove cured material mechanically.

Surface Preparation

Clean the area/duct to be grouted with water before the application of Vetogrout CG513. Drain any free water.

Additional Information
Health & Sefety

Vetogrout CG513 Contains reins that may cause sensitization by skin contact. Avoid contact with skin and eyes and inhalation of vapor. Wear suitable protective clothing, gloves, and eye/face protection. Barrier creams provide additional skin protection. Should accidental skin contact occur, remove immediately with a resin-removing cream, followed by soap and water. Do not use solvent. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice. If swallowed, seek medical attention immediately. Do not induce vomiting.

Vetogrout CG513 is non-flammable.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any liability, either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the technical data sheets' specifications upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Vetoanchor EG346
Epoxy resin twin cartridge anchoring grout

">

Epoxy resin twin cartridge anchoring grout

Vetocrete FC803
High strength structural fine shotcrete

">

High strength structural fine shotcrete

Vetocrete CC806
High strength structural shotcrete

">

High strength structural shotcrete

Vetogrout CG510

Multipurpose universal cementitious non-shrink grout

Vetogrout CG518
Chloride free nonmetallic non-shrink grout

">

Chloride free nonmetallic non-shrink grout

view more
Featured Product
Vetoprime CP436
(Formerly Known as Vetoprime CP437)

Corrosion inhibitor for steel reinforcement accepting cementitious repair or concrete

">

(Formerly Known as Vetoprime CP437)

Corrosion inhibitor for steel reinforcement accepting cementitious repair or...

Uses
Ideally designed as corrosion protection for steel reinforcement in the concrete repair systems.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com