Concrete Repairs & Grouts
Vetogrout UR711

Flexible non-foaming polyurethane injection resin

Uses
Injection of concrete and masonry cracks to form a flexible seal.
Used in conjunction with Vetogrout UR710 for crack injection in wet conditions.
Crack injection in live crack cases.
Fast Download
Technical Information
Product Description

Vetogrout UR711 is a two-part solvent-free, low viscosity, polyurethane resin system. When mixed in the proportions supplied, it reacts to form a tough, slightly flexible resin. Vetogrout UR711 has good adhesion to concrete and masonry, and when injected into cracks, it allows some movement without loss of bond.
Vetogrout UR711 is used in conjunction with Vetogrout UR710 to form a permanent seal in cracked concrete.

Advantages
  • Low viscosity with maximum crack penetration.
  • Excellent adhesion to both dry and moist substrates.
  • Flexible; it allows for movement accommodation in live cracks.
  • Withstands high hydrostatic pressure.
  • Impermeable.
COMPLIANCE STANDARD
  • ACI 546R: Guide for concrete repair.
  • ICRI Guideline No. 340.1-2006
  • BS 6319
Packaging & Coverage
  • - Vetogrout UR711 is supplied in a 5 Liters Kit. Theoretical Yield: 5 liters.
    - Vetorep ER350 is supplied in 1 & 5 kg Kit. Theoretical Yield - 1.7 kg/m2/mm.
    - Vetonit Solvent XX400 is supplied in 4 Liter Cans. Theoretical Yield - 4 liters.

Stated consumption data are for general guidance. Actual consumption depends on the nature of substrate, method of application, and wastage.

Shelf Life & Storage

Vetogrout UR711 original sealed containers have a shelf life of 6 months @ 20ºC, provided it is stored clear of ground in dry shaded and temperature-controlled conditions.
If stored at high temperatures and/or high humidity conditions, the shelf life may be reduced to 2 to 3 months.

Application Information
Instructions for use

Vetogrout UR711 application

Thoroughly mix the entire hardener and base resin contents until the liquid becomes clear.

Use Vetogrout UR711 with standard injection equipment having closed containers. The injection pressure should be at least 0.4 N/mm2 (4 bar).

Only mix sufficient resin that can be used within the pot life of the material.

Making Good

Remove the packers or nipples. Make good any holes or voids with Vetorep ER350 and allow them to cure. The Vetorep ER350 can be ground off or softened with a blowlamp and peeled off. Do not allow to burn.

Cleaning

Remove Vetogrout UR711 and Vetorep ER350 from tools, equipment, and mixers with Vetonit Solvent XX400 immediately after use. Remove hardened material mechanically.

Surface Preparation

Preparation

Clean the surface and remove any dust, unsound or contaminated material, plaster, oil, paint, grease, corrosion deposits, or algae.

Preferably prepare the surface using high-pressure water jetting or light abrasive blasting, followed by thorough washing to remove dust and remaining particles.

If dirt alone, remove with wire brushes or similar mechanical means. Remove oil and grease deposits by steam cleaning, detergent scrubbing, or the use of a proprietary degreaser. Assess the effectiveness of decontamination by a pull-off test.

Blow the cracks and the treated surface with oil-free air to ensure complete removal of all dust and loose particles.

Ensure to blow dry the surfaces.

In the presence of running water, stop the flow must using Vetogrout UR710, which produces a rapid setting water-stopping foam (see separate datasheet). When the water is stopped, re-inject the cracks with Vetogrout UR711.

Seal all cracks and locate injection packers in place before injecting Vetogrout UR711.

Fixing injection packers

Fix the injection packers inserted into pre-drilled holes at intervals along the length of each crack. The distance between each packer will depend upon the width and depth of the crack. Spacing shall be close enough to ensure that the resin will penetrate along the crack to the next point of injection. This will normally be between 200mm to 500mm.

Seal the cracks' surface between the packers with a band of Vetorep ER350, 30mm to 40mm wide and 2mm to 3mm thick. Both sides of any cracks which go all the way through a wall or slab shall be sealed in this way. In the case of a wall or slab which is cracked all the way through, packers shall be located on both sides, with those at the back placed at midway points between those at the front.

Allow the Vetorep ER350 to cure for 8 hours at 35ºC. At low ambient temperature (5ºC to 12ºC), extend the curing time, and the applicator shall ensure that the surface sealant has adequately cured before continuing.

Attach one end of the injection hose to the lowest packer on vertical cracks or attach to either end of horizontal cracks.

Treat each crack in a single, continuous operation.

Prepare sufficient material before the commencement of the work.

Limitation

Design Considerations

Vetogrout UR711 is designed to form a permanently flexible seal in cracked concrete and masonry units for widths between 0.2 and 10mm.
Use Vetogrout UR711 to stabilize soil and create membrane barriers behind retaining walls.

Additional Information
Health & Sefety

Vetogrout UR711 contains Isocyanate. May cause sensitization by inhalation. During use, avoid contact with skin and eyes and inhalation of vapor. Wear suitable protective clothing, gloves, and eye/face protection. The use of barrier creams provides additional skin protection.
Should accidental skin contact occur, remove immediately with a resin-removing cream followed by soap and water. Do not use solvent. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice. If swallowed, seek medical attention immediately - do not induce vomiting. Use only in well-ventilated areas. In case of insufficient ventilation, wear suitable respiratory protective clothing.


Vetogrout UR711 and Vetorep ER350 are not flammable. Vetonit Solvent XX400 is flammable; keep away from sources of ignition and direct flame.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any liability, either directly or indirectly, arising from the use of its products because it has no direct or continuous control over where or how its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the technical data sheets' specifications upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Vetoanchor EG346
Epoxy resin twin cartridge anchoring grout

">

Epoxy resin twin cartridge anchoring grout

Vetocrete FC803
High strength structural fine shotcrete

">

High strength structural fine shotcrete

Vetocrete CC806
High strength structural shotcrete

">

High strength structural shotcrete

Vetogrout CG510

Multipurpose universal cementitious non-shrink grout

Vetogrout CG513
Free-flowing pre-bagged non-shrink cementitious cable grout

">

Free-flowing pre-bagged non-shrink cementitious cable grout

view more
Featured Product
Vetoproof CM740

Single component elastomeric crack-bridging cementitious waterproof membrane

Uses
Waterproof lining for swimming pools, water tanks, dams, canals, etc.
Wet-areas waterproofing while receiving tile adhesives and other renders.
Protecting concrete and masonry structures against ingress of chloride ions and carbonation.
As a crack isolation membrane in tile fixing assemblies.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com