Primers and Ancillary
Vetorel XT420

Water-based mold and form-work release agent

Uses
Vetorel XT420 is used to treat wooden and metal form-work or molds before casting concrete to facilitate stripping.
Minimizing concrete surface blemishes and pinholes.
Fast Download
Technical Information
Product Description

Vetorel XT420 is a single component milky liquid composed of synthetic oils, special emulsifying agents, and varied additives with high anti-adhesion properties towards the concrete. Vetorel XT420 provides the plywood surface with a water repellent film preventing concrete from adhering to the form-work resulting in a smooth, stainless concrete surface.

Advantages
  • Factory-controlled, single component, and easy to use.
  • Water-based, environment-friendly product.
  • Odorless and nonflammable.
  • Produces neat concrete surfaces by letting the air & water bubbles rise freely during vibration.
  • Minimize surface staining even with white cement-based concrete.
  • Adheres to all wooden or plywood form surfaces, as well as to synthetic or steel forms.
  • Ensure easy release and cleanability while extending the usable life of shuttering.
Packaging & Coverage

Vetorel XT420 supplied in 20 & 200 Ltr. Theoretical Coverage: 7 - 20 m2/Ltr.

Stated consumption data are for general guidance. Actual consumption depends on the nature of the substrate, method of application, and wastage.

Shelf Life & Storage

The original sealed container of Vetorel XT420 has a shelf life of 12 months, provided it is stored clear of ground in a dry, shaded place below 35ºC.

Colors
Milky liquid
Application Information
Instructions for use

Application

Vetorel XT420 is supplied in containers ready to use at the site without a need to premix operation. Apply Vetorel XT420 by brush, roller, or spraying machine.

Apply Vetorel XT420 on plywood or steel shutter before the first casting. After every use of form-work, the shutter should be re-coated lightly with Vetorel XT420.

Do not over-apply Vetorel XT420 on the form-work. Excessive material should be allowed to drain before using the form-work.

Apply the product with a brush or preferably with a sprayer. It is advisable to apply Vetorel XT420 at least two hours before using the shutter for best results.

Consult Saveto technical department for any additional information.

Cleaning

Clean tools with water promptly before material hardens. Remove hardened material mechanically.

Surface Preparation

All form-work, clean shutter surfaces from deposits of rust, concrete, oil, or other materials. The product is ready to use without any dilution.

Limitation

Do not mix the product with water as it will lose its properties.

Do not mix with other materials.

Do not apply the product at a temperature less than +5ºC.

Vetorel XT420 should be checked for its suitability when concrete is steam cured. Also, carry out the prior tests for its suitability when gypsum or colored mixes are being used.

For further information contact our technical department.

Additional Information
Health & Sefety

Vetorel XT420 is harmful; therefore, avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. In case of contact with eyes, clean immediately with plenty of clean cold water and seek medical advice if irritation persists.

Vetorel XT420 is  non-flammable.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products because it has no direct or continuous control over where or how its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the technical datasheets' specifications upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Ready Mix Bond
Multi-purpose bonding agent & admixture

">

Multi-purpose bonding agent & admixture

Saveto Bond 2
Multipurpose low viscosity bonding agent & admixture

">

Multipurpose low viscosity bonding agent & admixture

Vetobond PB436
Polymeric soil stabilizer

">

Polymeric soil stabilizer

Vetobond PB434
Polymeric bonding agent, waterproof mix enhancer & primer

">

Polymeric bonding agent, waterproof mix enhancer & primer

Vetobond PB433
Versatile resin adhesive, cement modifier, bonding agent & sealer

">

Versatile resin adhesive, cement modifier, bonding agent & sealer

view more
Featured Product
Vetoset CA547

Polymer modified water-resistant adhesive for fixing pool, fountain & water tank tiles.

 

Uses
For use in all types of tiles for water tanks, swimming pools, fountains, and submerged conditions.
Tiling on smooth concrete surfaces, lightweight bricks, blocks, plasterboards.
Tiling on wall surfaces that are plastered with Saveto products.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com