Tiling Systems
Pool Grout

Water-resistant grout for swimming pool tile joints

Pool Grout is specifically designed for grouting all types of tiles for swimming pools, fountains, water tanks, and submerged conditions.
Grouting of walls and floor joints subjected to a varying range of dry or humid conditions.
Suitable for use with both ceramic and marble tiles.
Fast Download
Saveto Tile Adhesives & Grouts for General Purposes Brochure
download (*.pdf 2.00Mb)
Technical Information
Product Description

Vetonit Pool Grout is a polymer-modified cementitious tile grout composed of hydraulic binders, selected aggregates, special additives, and polymers. It is supplied as a dry powder in pre-weighed bags ready to use on-site, which requires only the addition of clean water to produce easily workable mortar. Vetonit Pool Grout is ideal for jointing Ceramic Tiles, Marbles. Vetonit Pool Grout is applied in thickness from 2-4 mm for wall tiles and 3-8 mm for floor tiles.

  • Factory controlled pre-blend ensures consistently high quality. 

  • Requires only the addition of water on-site at the time of usage.

  • Easy tile installation that enables high productivity. 

  • Superior workability. 

  • Excellent bonding on a variety of ceramic tiles available in the local market.

  • Water & weather resistance.

  • Suitable for internal &  external applications.

  • Suitable for horizontal & vertical surfaces.

  • BS: EN 13888

  • SASO ISO 13007-3,4 as CG 2AW

Packaging & Coverage

Pool Grout is supplied in 25Kg Bag.


  • Wall: 0.3 - 0.5 Kg/LM/3mm Joint
  • Floor: 0.5 - 0.8 Kg/LM/5mm Joint

Stated consumption data are for general guidance. Actual consumption depends on the nature of substrate, method of application, and wastages.

Shelf Life & Storage

The original sealed bag of Vetonit Pool Grout has a shelf life of 12 months, provided it is stored clear of ground in a dry, shaded place below 35ºC.

Colored Powder
Application Information
Instructions for use


For the preparation of Vetonit Pool Grout mortar, pour into a container 7-8.5 Liters of water for 25Kg bag of Vetonit Pool Grout. Add the powder to the water and mix with a low-speed electric drill fitted with a suitable paddle for 3-4 minutes until achieving a uniform, lump-free consistency. Allow the mixed material to stand for about 10 minutes and remix briefly without adding water.

Blend Vetonit Pool Grout manually for small quantities and maintain the correct mixing ratio of powder to water.

If required, add 0.5 Ltr of Vetobond AB432 to the mixing water, followed by powder's addition. Use the mixed material within 1 hour.

Do not add water to the mixture once the mortar grout starts to harden.


grouting trowel, a rubber spatula, or a sponge.

Spread the mixed grout diagonally across the tile joints and firmly press it with a rubbing pad covered with a sponge rubber spatula to ensure filling all the gaps.

Remove excess grout that remains on tiles using the same tool.

After the grout initially dries, from 15-30 minutes, depends on the ambient temperature & humidity, clean the tiles and remove all excess material with a wet sponge.

After full drying, clean the surface of the tiles with a dry cloth or dispensable cotton towels.

When washing & drying the tiles, ensure not to rub the tile joints too deep.

Keep the grout moist for the first 2 days after application to ensure achieving good hardened properties.


Clean tools and equipment with water immediately after use. Hardened materials will require removal by mechanical means.

Surface Preparation

Remove all tile adhesive excess that is at a level higher than half of the tile thickness.

All the joints should be free from dust, loose materials & traces of foreign materials, etc. Neutralize the tiles' water absorption by applying clean potable water.

Do not leave water pooling in the joints.

Additional Information
Health & Sefety

Vetonit Pool Grout is highly alkaline; therefore, avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be washed with soap & water. In case of eye irritation, immediately wash with a copious amount of clean cold water. Seek medical advice.

Vetonit Pool Grout is non-flammable.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products because it has no direct or continuous control over where or how its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the technical datasheets' specifications upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Ceramic Tile Fix

Weather-resistant cementitious adhesive for ceramic tiles

Pool FIX

Polymer modified water resistant adhesive for fixing swimming pools, fountains & water tanks tiles


Porcelain Tile Fix

Polymer modified weather resistant adhesive for porcelain tiles.

Premium Project Fix

High quality ceramic tile adhesive for projects.


Premium Fix

Water resistant premium quality ceramic tile adhesive


view more
Featured Product
Vetoset CA544

Specialty polymer modified cementitious adhesive for glass blocks and glass mosaic tiles

As an adhesive for glass block.
As an adhesive for glass mosaic tiles.
Internal and external applications.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com