Tiling Systems
Premium Fix

Water resistant premium quality ceramic tile adhesive

 

Uses
For ceramic tiles with normal open time.
Tiling on smooth concrete surfaces, lightweight bricks, blocks, plasterboards.
Suitable for dry & wet conditions.
Fast Download
Catalogues
Saveto Tile Adhesives & Grouts for General Purposes Brochure
download (*.pdf 2.00Mb)
reference projects
Project:
Baha University, Administration Building
Location:
Saudi Arabia
Description:
Administration Building
Contractor:
Al Joudah
Consultant:
Otaishan Consulting
Technical Information
Product Description

Premium Fix is a cementitious mortar adhesive composed of hydraulic binders, selected aggregates, and special additives. It is supplied as a dry powder in pre-weighed bags ready to use on-site, which requires only the addition of clean water to produce easily workable mortar. Premium Fix is ideal for fixing Ceramic Tiles, Terrazzo Tiles. Premium Fix is applied in thickness from 3mm to 10mm, depending upon the substrate's type of tiles and quality.

Advantages
  • Factory controlled pre-blend ensures consistently high quality.
  • Requires only the addition of water on-site at the time of usage.
  • Easy tile installation that enables high productivity.
  • Superior workability.
  • Excellent Adhesion to a variety of ceramic tiles available in the local market.
  • Water-resistant
  • Suitable for internal applications
  • Suitable for horizontal & vertical surfaces
COMPLIANCE STANDARD
  • BS:EN 12004 as C1T
  • SASO ISO 13007-1 as C1T
Packaging & Coverage

Premium Fix supplied in 20 Kg Bags.

Coverage:

Wall: 6-6.5 m²/bag 20 kg
Floor: 4.5 – 5.5 m²/bag 20 kg

Stated consumption data are for general guidance. Actual consumption depends on the nature of the substrate, method of application, and wastages.

Shelf Life & Storage

An original sealed bag of Premium Fix has a shelf life of 12 months, provided it is stored clear of ground in a dry, shaded place below 35ºC.

Colors
White powder
Application Information
Instructions for use

Mixing

For the mortar adhesive preparation, pour into a container 4.8-6.5 liters of water for each 20 Kg bag of Premium Fix.

Add the powder to the water and mix for 3-4 minutes using a low- speed electric drill fitted with a  suitable paddle until achieving a uniform, lump-free consistency. Allow the mixed material to stand for about 10 minutes and remix briefly without adding further water.

Blend Premium Fix manually for small quantities and maintain the correct amount of powder to water.

If required, add 0.5 Ltr of Vetobond AB432 to the mixing water, followed by powder's addition. Use the mixed material within 2 hours.

Do not add water to the mixture once the mortar adhesive starts to harden.

Application

Spread the mixed mortar adhesive, and firmly press it onto the surface that will be tiled; work with a notched trowel. Spread the mortar adhesive to an area that can be tiled within 10-15 minutes. Press the tiles firmly over the mortar adhesive and immediately knock them into the desired position. Adjust the position of the tiles, if required, within its adjustability time of  10-15 minutes after installation.

Allow the installed tiles to remain undisturbed for at least 48 hours. Mortar adhesive must not rise between the tile joints higher than halfway the thickness of the tiles. It is recommended to use Vetonit Tile Grout to fill the joint gaps after 2 days of tile installation.

Cleaning

Clean tools and equipment with water immediately after use. Remove the hardened material using mechanical means.

Surface Preparation

The surface should be sound, clean, free from loose material, oil, grease, laitance, dirt, curing compound, etc.

Wet all surfaces (except gypsum board) with clean water before Premium Fix's application. The surface should appear damp with no water pooling.

Additional Information
Health & Sefety

Premium Fix is highly alkaline; therefore, avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be washed with soap & water. In case of eye irritation, immediately wash with a copious amount of clean cold water. Seek medical advice.

Premium Fix is non-flammable.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products because it has no direct or continuous control over where or how its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the technical datasheets' specifications upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Ceramic Tile Fix

Weather-resistant cementitious adhesive for ceramic tiles

Pool FIX

Polymer modified water resistant adhesive for fixing swimming pools, fountains & water tanks tiles

 

Pool Grout

Water-resistant grout for swimming pool tile joints

Porcelain Tile Fix

Polymer modified weather resistant adhesive for porcelain tiles.

Premium Project Fix

High quality ceramic tile adhesive for projects.

 

view more
Featured Product
Vetotherm Flex
Cementitious based adhesive and base coat for EIFS / ETICS

">

Cementitious based adhesive and base coat for EIFS / ETICS

Uses
Expanded and extruded polystyrene and rock wool adhesive on cementitious substrates, masonry, and gypsum boards.
Fiber mesh reinforced base coat as part of EIFS / ETICS systems.
Ready to receive a wide range of decorative finishes.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com