Primers and Ancillary
Vetobond EB430

Solvent-free epoxy bonding agent to bond old to new concrete

Uses
Bonding old to new concrete.
Elimination of cold joints resulting from casting stops.
As a primer for bonding cementitious repair materials (Vetorep range of products).
Bonding of cementitious screeds to concrete substrates.
Fast Download
Technical Information
Product Description

Vetobond EB430 is based on solvent-free epoxy resins containing pigments and fine fillers. It is supplied as a two-component material in pre-weighed quantities, ready for on-site mixing and use. The product is used in external and internal applications on horizontal surfaces or on vertical surfaces where mortar or concrete can be supported by formwork. The long ‘open’ life makes it suitable for formwork or where additional steel reinforcement is fitted. The product is ideal for roads, bridges, pavements, loading bays, and factories, and bonded or granolithic floor toppings.

Advantages
  • Adhesive bond to concrete will always exceed the tensile strength of the host concrete.
  • Suitable for use on damp and dry concrete.
  • Odorless and non-flammable remains tacky for 48 hours at 22ºC.
  • Resistant to hydrolysis, used externally and internally.
  • High mechanical properties.
  • Excellent bond to concrete, masonry, stonework, plaster, and cement boards.
COMPLIANCE STANDARD

ASTM C 881/881M-13 (Standard Specification for Epoxy-Resin-Base Bonding Systems for Concrete) as Type I, II, III, IV & V - Grade 3 class B & C

Packaging & Coverage

Vetobond EB430 is supplied in 5 Liters Kit.
Coverage: 5-8  m2/Liter.

Stated consumption data is for general guidance. Actual consumption depends on the nature of substrate, method of application, and wastage.

Shelf Life & Storage

The original sealed container of Vetobond EB430 has a shelf life of 12 months, provided it is stored clear of ground in a dry, shaded place below 35ºC.

Application Information
Instructions for use

Design Criteria

Vetobond EB430 has an overlay time of 24 hours at 22ºC, 12 hours at 30ºC, or 8 to 10 hours at 35ºC, making it more suitable for use where additional steel reinforcement and formwork has to be fitted or where temperatures are high.

Application

Apply Vetobond EB430 as soon as the mixing process completes. Brush Vetobond EB430 or spray it to the prepared surfaces. The new concrete or screed may be applied to the coated substrate up to 24 hours after application at 22ºC or up to 12 hours at 30ºC, or between 8 to 10 hours at 35ºC. However, leave the coated substrate for one hour before placing the new concrete or screed. Take care to achieve an unbroken coating, where Vetobond EB430 is used as part of a repair system to form a substrate/repair barrier. Apply one coat and allow to gel. Apply a second coat and use it as the bonding coat. In some situations (e.g., sprayed concrete repairs), it may be advantageous to scatter dust-free sharp sand over this coat and leave it to harden. As soon as the Vetobond EB430 has been applied, any required steel reinforcement and/or formwork should be elected and fixed securely in place.

Cleaning

Remove Vetobond EB430 from tools, equipment, and mixers with Vetonit Solvent 1 immediately after use.
Hardened material can only be removed mechanically.

Surface Preparation

Clean all surfaces and remove any dust, unsound material, plaster, oil, paint, grease, corrosion deposits, or algae. Roughen the surfaces, remove any laitance and expose aggregate by light scabbling or grit-blasting. Remove oil and grease deposits by steam cleaning, detergent scrubbing, or the use of a proprietary degreaser. A pull-off test should then assess the effectiveness of decontamination and the soundness of the substrate. Any steel reinforcement and formwork should be prepared, cut to size and shape, and made ready for assembly before mixing commences.

Ensure mixing Vetobond EB430 thoroughly. Stire the ‘hardener’ and ‘base’ components separately before mixing to disperse any settlement. Pour the entire content of the ‘hardener’ tin into the ‘base’ tin. Mix the two materials thoroughly using a suitable slow-speed drill and mixing paddle for 2 minutes until obtaining a fully uniform color. Scrap the sides of the tin, and continue mixing for a further 1 minute. Slowly add the Reducer part and mix for 3 minutes.

To facilitate mixing and application at temperatures below 22ºC, the separate components should be warmed in hot water up to a maximum temperature of 25ºC before beginning to mix. If heated to 25ºC, the subsequently mixed material will need to be used more speedily as the pot-life will be reduced to 4 hours. Alternatively, Store the material in an environment heated to 22ºC and remove it immediately before use.

Additional Information
Health & Sefety

Vetobond EB430 should not come in contact with skin or eyes or be swallowed. Ensure adequate ventilation and avoid inhalation of vapors. Some people are sensitive to resins, gardeners, and solvents. Wear suitable protective clothing, gloves, and eye protection. Suppose working in confined areas, use suitable respiratory protective equipment.

The use of barrier creams provides additional skin protection.

In case of contact with skin, remove immediately with resin-removing cream followed by washing with soap and water.

Do not use solvent. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice. If swallowed, seek medical attention immediately – do not induce vomiting.

Vetobond EB430 is non-flammable.

Refer to the product Material Safety Data Sheet for further information.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any liability, either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Ready Mix Bond
Multi-purpose bonding agent & admixture

">

Multi-purpose bonding agent & admixture

Saveto Bond 2
Multipurpose low viscosity bonding agent & admixture

">

Multipurpose low viscosity bonding agent & admixture

Vetobond PB436
Polymeric soil stabilizer

">

Polymeric soil stabilizer

Vetobond PB434
Polymeric bonding agent, waterproof mix enhancer & primer

">

Polymeric bonding agent, waterproof mix enhancer & primer

Vetobond PB433
Versatile resin adhesive, cement modifier, bonding agent & sealer

">

Versatile resin adhesive, cement modifier, bonding agent & sealer

view more
Featured Product
Vetobond PB436
Polymeric soil stabilizer

">

Polymeric soil stabilizer

Uses
Sand stabilization in embankments, runways, and dunes.
Dust prevention & erosion control.
Rural walkways and paths.
Open desert sand stabilization and sand storm inhibition.
Landscaping applications.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com