Tiling Systems
Vetofill EG455

Water cleanable, chemical resistant, waterproof epoxy tile grout

Filling tile joints of virtually all types of tiles up to 10 mm.
Chemical processing plants and pharmaceutical plants.
Industrial Kitchens, food plants, and hospitals.
Swimming pools and aquariums.
Hospitals and clinics.
Fast Download
Saveto Tile Adhesives & Grouts Professional Product Range Brochure
download (*.pdf 2.34Mb)
Technical Information
Product Description

Vetofill EG455 is a three-component epoxy-based, water cleanable, chemical resistant, and waterproofing tile grout used with most types of tiles, including ceramic, porcelain, glass mosaic, marble, granite,...etc. The product is composed of 3 components consisting of a resin base, hardener, and selected fillers.

  • Easy to apply.
  • Fast return to service and reinstatement.
  • Excellent mechanical and physical properties.
  • High bond strength.
  • High chemical resistance.
  • Water cleanable.
  • ANSI A118.3
  • ANSI A108.6
  • BS EN 12004 as RG2AW
  • SASO ISO13007-3 as RG2AW
Packaging & Coverage

Vetofill EG455 is supplied in 3 components 8Kg kit.

Theoretical Yield of 4.5 Liters.

Stated consumption data are for general guidance. Actual consumption depends on the nature of substrate, method of application, and wastages.

Shelf Life & Storage

The original sealed containers of Vetofill EG455 have a shelf life of 12 months, provided it is stored clear of ground in a dry, shaded place below 35ºC.

Colored Paste
Application Information
Instructions for use


To ensure proper mixing, use a mechanically powered mixer or heavy-duty slow speed drill fitted with a suitable paddle.

Stir the base (component A) and the hardener  (Component B) individually to disperse any settlement. Pour the entire contents of the base and hardener into a suitable size container and mix mechanically for 2 minutes.  Add the Filler (component C) and mix for another 3 minutes until achieving a uniform, lump-free consistency.


Fill the mixed grout into the joints using a rubber trowel or a hand-operated gun and cartridges; clean excess grout with a wet sponge.

After grouting with Vetofill EG455, within 80 minutes from grouting, clean the joints and excess grout by using a wet sponge.


Clean tools and equipment with water immediately after use. Remove the hardened material using mechanical means.

Surface Preparation

The substrate should be sound, clean, free from loose material, grease, laitance, dirt, or any other substance that might impair the bond's quality with the substrate.

  • Do not apply/cure at a temperature below 5ºC.
Additional Information
Health & Sefety

Vetofill EG455 should not come into contact with skin and eyes or be swallowed. Ensure adequate ventilation and avoid inhalation of vapors. Some people are sensitive to resins, gardeners, and solvents. Wear suitable protective clothing, gloves, and eye protection. If working in confined areas, suitable respiratory protective equipment must be used. The use of barrier creams provides additional skin protection. In case of skin contact, rinse with plenty of clean water, then cleanse with soap and water. Do not use solvent. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice. If swallowed, seek medical attention immediately - Do not induce vomiting.

Vetofill EG455 is non-flammable.

For further information, please refer to the material safety data sheet.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products because it has no direct or continuous control over where or how its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the technical datasheets' specifications upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Ceramic Tile Fix

Weather-resistant cementitious adhesive for ceramic tiles

Pool FIX

Polymer modified water resistant adhesive for fixing swimming pools, fountains & water tanks tiles


Pool Grout

Water-resistant grout for swimming pool tile joints

Porcelain Tile Fix

Polymer modified weather resistant adhesive for porcelain tiles.

Premium Project Fix

High quality ceramic tile adhesive for projects.


view more
Featured Product
Vetotherm Mesh

Glass fiber reinforcement meshes designed for use with external thermal insulation coating systems.

Reinforcement of ETICS/EIFS body and topcoats.
Strengthening of corners and sharp angle sections.
Reinforce against crack formation in wall coatings.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com