High quality premixed surface crack filler
Vetonit Crack Filler is composed of a fine filler, high-quality white cement, bonding chemicals, and special additives. It is supplied as a dry powder in pre-weighed bags ready to use on-site, which requires only addition of clean water to produce a cohesive mix. Vetonit Crack Filler is a high-quality product for repairing static cracks and provides a very smooth surface finish for subsequent application of paints, decorative coatings & wallpapers. Vetonit Crack Filler can be applied in crack thickness from scrape coat to 4 mm.
Vetonit Crack Filler is supplied in 1.5 & 25 Kg Bag
Consumption: 0.8 - 1.0 Kg/m²/ 1mm Thickness
Stated consumptions data are for general guidance. Actual consumption depends on the nature of the substrate, method of application and wastage.
An original sealed bags of Vetonit Crack Filler has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 25ºC.
For mechanical mixing add to the mixing container 9.5-11.0 liters of water for each 25 Kg bag of Vetonit Crack Filler or 0.57-0.66 litres/1.5 kg small bag. Add the powder to the water and mix with a mechanical plaster mixer or low-speed electric drill fitted with a suitable paddle for 3-4 minutes, until a uniform, lump-free consistency is achieved.
Leave the mixed material to stand for 10 min and briefly remix without the addition of water. Manual mixing is allowed for small batch quantities and mix for approx. 1-2 min or when a homogenous mix is achieved.
When required add 0.5 Ltr of Vetonit Bond 2 to the mixing water and adjust the water requirement accordingly for each 25 kg bag or 30 ml of Vetonit Bond 2 per 1.5 kg bag. Follow the same mixing procedure as above.
Mixed material must be used within 2 hours.
Do not add water once the mixed filler mortar starts to stiffen or harden.
Vetonit Crack Filler is generally applied in two coats for wide and deeper cracks.
Apply Vetonit Crack Filler to the substrate by pressing the filler firmly into the cracks using a flat putty trowel.
Use Vetonit Joint Tape to cover the treated surface after filling the cracks. Use Vetonit Bond 2 for fixing tape for better adhesion.
Use alkali-resistant paints & coatings as a final decorative finish.
Vetonit crack filler generally may not require curing. However in extreme weather conditions (T > 45 C° and RH < 50% ) Vetonit crack filler should be cured by spraying clean water every 8-12 Hrs for a minimum of 2 days.
All tools should be cleaned immediately after finishing by water. Hardened materials can be cleaned mechanically.
The surface should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc.
Prior to Vetonit Crack Filler application, wet the entire surfaces with clean potable water and allow the surfaces to become damp at the time of application.
Vetonit Crack Filler is highly alkaline therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be wash with soap & water. In case of eye irritation, immediately wash with a copious amount of clean cold water. Seek medical advice.
Vetonit Crack Filler is non-flammable.
For further information, please refer to the material safety data sheet.
Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
PVA copolymer based high-quality putty
Gypsum surfaces skim and finish compound
Water resistant internal use premix smooth cement coating
Water resistant external use premix smooth cement coating
Premium quality premixed compound for gypsum board joints
Universal cementitious grout for large thickness repair & grouting