Renders & Finishes
Vetonit Putty WR

Water resistant high quality premixed putty

Uses
Leveling of minor surface undulations
Applied externally & internally in wet to dry conditions onto the walls & ceilings such as bathrooms & kitchens
On concrete and plastered surfaces that are smooth and also precast concrete surfaces
Suitable for use over surfaces that are plastered with Saveto products and on gypsum boards
Fast Download
Technical Information
Product Description

Vetonit Putty WR is composed of fine fillers, bonding chemicals, and high-performance additives. It is supplied as a dry powder in pre-weighed bags ready to use on-site, which requires only addition of clean water to produce a cohesive mix. Vetonit Putty WR is a high-quality product as a thin underlayment to repair undulations and provides a very smooth surface finish ideal for subsequent application of paint & decorative coatings. Vetonit Putty WR can be applied generally in thickness from 1 mm to 3 mm.

Advantages
  • Factory controlled pre-blend ensures consistent high quality
  • Requires only addition of water on-site at the time of usage
  • Suitable for External & Internal applications
  • Water-resistant
  • Easy application with superior finishing achieved in minimum efforts
  • Strong adhesion on a variety of substrates
  • Concrete and plastered walls & ceilings
  • A very smooth finish can be achieved
  • Suitable for humid & dry conditions
COMPLIANCE STANDARD
  • BS EN 1015-12 
Packaging & Coverage

Vetonit Putty WR is supplied in 20 Kg Bag
Consumption: 1.0 - 1.2 Kg/m2/1mm Thickness

Stated consumptions data are for general guidance. Actual consumption depends on the nature of the substrate, method of application and wastage.

Shelf Life & Storage

Original sealed bags of Vetonit Putty WR has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 25ºC.

Colors
White color powder
Application Information
Instructions for use

Mixing
For mechanical mixing add to the mixing container 7.6-8 liters of water for each 20 Kg bag of Vetonit Putty WR. Add the powder to the water and mix with a mechanical plaster mixer or low-speed electric drill fitted with a suitable paddle for 3-4 minutes, until a uniform, lump-free consistency is achieved.
Leave the mixed material to stand for 10 min and briefly remix without the addition of water.
Manual mixing is allowed for small batch quantities and mix for approx. 1-2 min or when a homogenous mix is achieved.
When required add 1 liter of Vetonit Bond 2 to the mixing water and adjust the water requirement accordingly for each 20kg bag. Follow the same mixing procedure as above.
Mixed material must be used within 3 hours. Do not add water once the mixed filler mortar starts to stiffen or harden.

Application
Vetonit Putty WR is generally applied in single or double coats. Apply Vetonit Putty WR to the substrate by pressing the putty firmly, work the mixed material to a smooth level using a flat trowel. Apply a second coat as necessary once the first coat has initially set.
Once Vetonit Putty WR is applied, It is recommended to apply one coat of alkali-resistant primer followed by two coats of acrylic emulsion paint or other suitable coatings.

Curing
Vetonit Putty WR is self-curing and does not require water treatment. However, when used as a final finish it is recommended to apply a single coat of Bond Pure to perform as a surface enhancer and curing compound that will naturally disintegrate with time.

Cleaning
All tools should be cleaned immediately after finishing by water. Hardened materials can be cleaned mechanically.

Surface Preparation

The surface should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc.
Prior to the Vetonit Putty WR application, wet the entire surfaces with clean potable water and allow the surfaces to become damp at the time of application.

Additional Information
Health & Sefety

Vetonit Putty WR is highly alkaline therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application.
Any skin contact should be wash with soap & water. In case of eye irritation, immediately wash with a copious amount of clean cold water. Seek medical advice.
Vetonit Putty WR is non-flammable.
For further information, please refer to the material safety data sheet.

Important note
Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification. 

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Saveto Putty Fine

PVA copolymer based high-quality putty

 

Vetogyps Compound
Gypsum surfaces skim and finish compound

">

Gypsum surfaces skim and finish compound

Vetonit Crack Filler

High quality premixed surface crack filler

Vetonit Finish WR

Water resistant internal use premix smooth cement coating

Vetonit Finish WR EG

Water resistant external use premix smooth cement coating

view more
Featured Product
Vetonit PBL

Saveto block reinforcement access-ories ladder type

 

Uses
As vertical bars to reinforce masonry block works
Reinforces block walls against wind effect.
Withstand the loading of material against the wall.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com