Fiber reinforced cementitious premixed plastering/rendering material
Premix Plaster SF is a cement based plastering material composed of hydraulic binders, selected graded aggregates, special fibers, and special additives. It is supplied as a dry powder in bags/bulk ready to use on site, which requires only the addition of clean water to produce cohesive mortar. Premix Plaster SF is specially designed for application by spray machine and it can be used manually if required, and contains special shrinkage control additive and provides good adhesion with uniform color surface. Premix Plaster SF can be applied at thicknesses ranging from 10mm to 25mm.
Premix Plaster SF supplied in 50 Kg Bag or Bulk. Yield - 31.25 Liters.
Original sealed container of Premix Plaster SF has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 25ºC
Premix Plaster SF is designed to be used at thicknesses betwen 10 and 25mm in a single application. The product can be applied on block walls without the need to use a scratch coat as long as the substrate is properly neutralized prior to application.
Add to the mixing container 6.5-8.5 liters of water for each 50 Kg bag of Premix Plaster SF. Add the powder to the water and mix with a mechanical plaster mixer or low speed electric drill fitted with a suitable paddle for 3-4 minutes, until a uniform, lump-free consistency is achieved.
For application using PFT plastering machine, the water flow rate is 350- 550 lit/hr depending on the status of the rubber pump. Mixed material should be used within 90 min.
Do not add water to the mix once the mixed mortar start to harden.
Smooth Concrete Surfaces
Apply Spatter Dash SB prior to the application of Premix Plaster SF.
Premix Plaster SF can be applied in a single or multiple layers on rough surfaces. On smooth surfaces it should be applied subsequent to the application of a spatterdash coat.
Rod or level to a uniform thickness when the plaster starts to set, then follow smoothing the material to the desired appearance.
For multiple follow the practice in ASTM C926, 10 - 15 mm/layer with a rough finish, with curing for two days /layer prior application the second one, the final layer to be finished as desired.
After the surface appears stiff but still moist, follow the smoothing the material to achieve a desired appearance.
Premix Plaster SF is best cured by spraying water on its surface every 8-12 hrs for a minimum of 3 days. During hot & dry conditions allow curing for minimum of 5 days. It will help to obtain high mechanical strengths and minimize the risk of surface cracks.
Substrate should be sound, clean, free from loose material, grease, laitence, dirt curing compound, or any other substance that might impair the quality of bond with the substrate. Prior to Premix Plaster SF application, damp the entire surfaces with clean potable water. The substrate should be neutralized surface at the time of Premix Plaster SF application.
Make sure the substrate is suitable for the application of Premix Plaster SF, in case of doubt, try on sample area to assess its suitability.
Do not apply the product under direct rain, extreme wind, and at temperatures below +5ºC or above +45ºC.
Tools should be cleaned with water before the mortar hardens. After the hardening its residuals can be removed mechanically.
Premix Plaster SF is highly alkaline therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be washed with soap and water. In case of eyes irritation, immediately wash with copious amount of clean cold water. Seek medical advice. Premix Plaster SF is non-flammable.
For further information, please refer to material safety data sheet.
Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
High quality light weight premixed acoustic plaster
High quality gypsum plaster.
Premixed cementitious masonry grout
Sprayable premixed plaster
Light weight gypsum perlite plaster
Polymer modified water resistant cementitious top coat