Plasters & Masonry
Masonry Grout Filler

Premixed cementitious masonry grout

Apply Masonry Grout Filler on cement-based masonry blocks, masonry units, behind marble and cement panels, tiles or slabs, etc.
Masonry Grout Filler is suitable for the application behind gypsum boards.
Fast Download
Saveto Decorative Coating Brochure
download (*.pdf 2.78Mb)
Saveto Plastering Systems Technical Guide
download (*.pdf 9.93Mb)
reference projects
King Khalid University
Saudi Arabia
Housing & Parking projects
Al Jabreen Contracting
Parking: Zuhair Fayez Housing: Saud Consult
Technical Information
Product Description

Masonry Grout Filler is a fine grout category defined by American Concrete Institute (ACI), and is composed of portland cement, natural sand, selected fine aggregates, and special additives. The Masonry Grout Filler contains admixtures following ASTM C 476, C207, C260 to meet the fine grout category. Masonry Grout Filler is supplied as a dry powder in pre-weighed bags ready to use on-site, which requires only the addition of clean water to produce pourable grout.  Masonry Grout Filler is ideal for grouting masonry blocks, masonry units, cores, and a filler behind marble slabs. 

  • Factory controlled pre-blend ensures consistently high quality.
  • Requires only the addition of water on-site at the time of usage.
  • Suitable for ME harsh weather conditions.
  • Easy application with uniform work flow enables high productivity & superior finishing.
  • Strong adhesion.
  • Good mechanical resistance.
  • Excellent workability.
  • ASTM C 476, C207
  • ASTM C 404, C260
  • ASTM C 150 Type 1
Packaging & Coverage

Masonry Grout Filler is supplied in 50Kg Bag.
Yield: 28.8 Lit wet/ (50Kg) bag powder

Stated consumption data are for general guidance. Actual consumption depends on the nature of the substrate, method of application, and wastage.

Shelf Life & Storage

The original sealed bag of Masonry Grout Filler has a shelf life of 12 months, provided it is stored clear of ground in a dry, shaded place, at temperatures between 5ºC - 35ºC.

Grey Powder
Application Information
Instructions for use


For the preparation of masonry grout mixture, pour into a container 6.5 - 8  liters of water for each 50 Kg bag of Masonry Grout Filler.

Slowly add the powder to the water while mixing with an electric drill fitted with a suitable paddle for 2 minutes. Then continue mixing at medium-high speed for another 2-3 minutes until achieving a uniform, lump-free pourable consistency mix. The total mixing time is 4-5 minutes approx.

Please do not add water to the mix once it starts to stiffen.


Pour the mixed material into the gap between masonry blocks, cement panels, or behind marble or gypsum board within the open time of 30-45 min.

Avoid air entrapment between the gaps while pouring the grout material.

For high lift grouting, the mixed material should be pumped or poured from a height to ensure the desired grout flow spread smoothly within the gaps.

We recommend using a mechanical grout pump for masonry grout placement as it will give more efficient filling and help in grout pumping in high rise structures.


Clean all tools immediately after finishing by water. Clean hardened materials mechanically.

Surface Preparation

The surface should be sound, clean free from loose materials, grease, laitance, dust, etc.

Additional Information
Health & Sefety

Masonry Grout Filler is highly alkaline; therefore, avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be wash with soap & water. In case of eye irritation, immediately wash with a copious amount of clean cold water. Seek medical advice.

Masonry Grout Filler is non-flammable.

For further information, please refer to the material safety data sheet.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products because it has no direct or continuous control over where or how its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the technical datasheets' specifications upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Acoustic Plaster

High-quality lightweight premixed acoustic plaster

Plaster Cement Perlite
Sprayable lightweight premixed plaster


Sprayable lightweight premixed plaster

Plaster Gypsum

High-quality gypsum plaster

Plaster Gypsum Perlite

Light weight gypsum perlite plaster

Plaster Mix M
Manual applied premixed plaster


Manual applied premixed plaster

view more
Featured Product
Vetogrout UR711

Flexible non-foaming polyurethane injection resin

Injection of concrete and masonry cracks to form a flexible seal.
Used in conjunction with Vetogrout UR710 for crack injection in wet conditions.
Crack injection in live crack cases.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718