Wall & Facade Systems
Vetotouch Marmo

Marble chip decorative exterior and interior finishing system

Marble chip finish designed for interior/exterior application.
On plastered, fair-faced concrete surfaces.
On block walls and pre-cast panels.
Applied in 5-10 mm thickness.
Fast Download
Saveto Decorative Coating Brochure
download (*.pdf 2.78Mb)
Vetotouch Effects
download (*.pdf 1.11Mb)
Saveto External Thermal Insulation Composite System - ETICS Guide
download (*.pdf 8.19Mb)
Technical Information
Product Description

Vetotouch Marmo is a cement-based decorative finish composed of hydraulic binders, selected aggregates, and special additives. It is supplied as a dry powder in pre-weighed bags ready to use on-site, which requires only the addition of clean water to produce easily workable mortar.

  • Factory-controlled pre-blend ensures consistently high quality.
  • Requires only the addition of water on-site at the time of usage.
  • Provides a variety of finishes using various colors and marble chip types.
  • Improved workability and curing.
  • Easy application with uniform workflow enables high productivity and superior finishing.
  • Strong adhesion on a variety of substrates.
  • Internal and external applications.
  • Weather-resistant.
  • UV stable pigment provides resistance to fading and eliminates the need for additional paint.
  • Suitable for humid and dry conditions.
  • BSEN 998-1
  • ASTM C926
  • BSEN 13914
Packaging & Coverage

Vetotouch Marmo is supplied in 25kg Bags.
Yield: 17 liters.

Stated consumption data are for general guidance. Actual consumption depends on the nature of substrate, consistency used, method of application, and wastage.

Shelf Life & Storage

The original sealed bag of Vetotouch Marmo has a shelf life of 12 months, provided it is stored clear of ground in a dry, shaded place below 35ºC.

Saveto Standard Colors
Application Information
Instructions for use


Add to the mixing container 5-5.5 liters of water for each 25kg bag of Vetotouch Marmo. Add the powder to the water and mix with a mechanical plaster mixer or low-speed heavy-duty electric drill fitted with a suitable paddle for 3-4 minutes until achieving a uniform, lump-free consistency. Leave the mixed material to stand for 10min and briefly remix without adding water.

For small batch quantities, mix manually for approx. 1-2 min or until achieving a homogeneous mix.
Add 0.5 to 1.0 liter of Vetobond AB432 to the mixing water and adjust the water requirement accordingly for each 25kg bag. Follow the same mixing procedure as described above.
Use the mixed material within 2 hours.
Do not add water once the mixed mortar starts to harden.


Apply Vetotouch Marmo in a single layer (5 - 10mm).

Apply the design, color scheme, and joints using a small amount of the mixture at a thickness of 2mm glued to the plastic spacers. Use the processed plastic spacers with the required lengths, and allow for a period of not less than 10 minutes to dry. Broadcast the wet surface mixture with marble chips; when the mixture begins to stiffen, compress the chips into the surface with a steel or plastic trowel to reach a homogeneous level with an attractive design.

Apply a coat of Vetoseal XX772 for protection against water penetration, chloride ion attack, freeze/thaw cycles, weathering, and airborne contaminants.


It is vital to cure Vetotouch Marmo surface with clean potable water 2 times a day for 3 days. During hot and dry conditions, extend the curing period for a minimum of 5-7 days. It will help to obtain high physical properties. An acrylic-based curing compound can be used.

To protect the final color look, it is recommended to apply one coat of Saveto Vetoseal product range (contact the technical department for advice).


Clean tools with water before the mortar hardens. After the hardening, remove its residuals mechanically only.

Surface Preparation

The substrate should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc.

Before the Vetotouch Marmo application, wet the entire surfaces with clean potable water. The surface should look damp at the time of the Vetotouch Marmo application.

Additional Information
Health & Sefety

Vetotouch Marmo is highly alkaline; therefore, avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be wash with soap & water. In case of eye irritation, immediately wash with a copious amount of clean cold water. Seek medical advice.

Vetotouch Marmo is non-flammable.

For further information, please refer to the material safety data sheet.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products because it has no direct or continuous control over where or how its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the technical datasheets' specifications upon its discretion without prior notification. 

Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Vetotouch Europa

Cementitious polymer modified decorative finish coat applied at thicknesses from 1 to 5mm

Vetotouch Graviatto

Grooved decorative finish coat

Vetotouch Monocouche

UV resistant pigmented premixed textured plaster

Vetotouch Serene

Cementitious polymer modified decorative finish coat applied at thicknesses from 1 to 3mm

Vetotouch Textura
Acrylic polymer modified decorative finish coat applied at thicknesses from 5 to 20mm


Acrylic polymer modified decorative finish coat applied at thicknesses from 5 to 20mm

view more
Featured Product
Vetogrout ER717

Low viscosity epoxy grout & injection resin

Restoration of the structural integrity of structural elements.
Injection of structural elements in retaining walls, beams, columns, shear walls, tanks, etc.
Grouting and static crack filling from 0.2 to 10 mm.
Base plate grouting in dynamic load situations.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com