Wall & Facade Systems
Vetotouch Monocouche

UV resistant pigmented premixed textured plaster

Internally or externally in wet & dry conditions onto block walls & rough surfaces.
On concrete surfaces that are smooth and also precast concrete surfaces with scratch coat applied first.
It can be applied up to 20mm thickness of the single-layer; however, it is recommended for two coat applications of 10mm each.
Fast Download
Saveto Decorative Coating Brochure
download (*.pdf 2.78Mb)
Vetotouch Effects
download (*.pdf 1.11Mb)
Saveto External Thermal Insulation Composite System - ETICS Guide
download (*.pdf 8.19Mb)
Saveto External Thermal Insulation Composite System - ETICS Guide
download (*.pdf 8.19Mb)
Saveto Plastering Systems Technical Guide
download (*.pdf 9.93Mb)
Technical Information
Product Description

Vetotouch Monocouche is a cement-based plaster coat composed of hydraulic binders, selected aggregates, special pigments, and high-performance additives. It is supplied as a dry powder in pre-weighed bags ready to use on-site, which requires only the addition of clean water to produce cohesive mortar. Vetotouch Monocouche is a high-quality product and suitable for external applications with marble chips.

  • Factory-controlled pre-blend ensures consistently high quality.
  • Requires only the addition of water on-site at the time of usage.
  • Uniform color/mass.
  • Improved workability & curing.
  • Easy application with uniform workflow enables high productivity & superior finishing.
  • Strong adhesion on a variety of substrates.
  • Internal & external applications.
  • Shrinkage control reduces surface cracks.
  • Suitable for humid & dry conditions.
  • Suitable for vertical & ceiling surfaces.
  • BSEN 998 - 1 , CSIV , WC 1
  • ASTM C926
  • Cement type: ASTM C150, type1
Packaging & Coverage

Vetotouch Monocouche is supplied in 50kg Bag or Bulk.

Yield: 32 Liters.

Stated consumption data are for general guidance. Actual consumption depends on the nature of substrate, consistency used, method of application, and wastage.

Shelf Life & Storage

The original sealed bag of Vetotouch Monocouche has a shelf life of 12 months, provided it is stored clear of ground in a dry, shaded place below 35ºC.

Colored Powder
Application Information
Instructions for use


For manual application, add to the mixing container 7.5-9 liters of water for each 50kg bag of Vetotouch Monocouche, or 9-10.5 liters/50kg bag for machine application. Add the powder to the water and mix with a mechanical plaster mixer or low-speed electric drill fitted with a suitable paddle for 3-4 minutes until achieving a uniform, lump-free consistency.

Leave the mixed material to stand for 10min and briefly remix without adding water.

Smooth Concrete Surfaces

Prepare the smooth concrete surface by applying a suitable Scratch Coat from Saveto depending on the surface.

For better adhesion to the substrate, add 0.5 Litter of Vetonit Bond 2 to the mixing water for each 50Kg bag or add 1 liter of Vetonit Plastering Bond to the mixing water referenced to the measured powder quantity, then follow the same mixing procedures as described above.

Use the mixed material within 1 hour. Do not add water once the mixed mortar starts to harden.


Apply Vetotouch Monocouche in a single or two coats on the prepared substrate by manual or machine application to achieve the desired thickness of 3-20mm.

Apply the mixed material using a spray machine or hawk & trowel technique. Rod or screed to uniform thickness, not exceeding 20mm for a single coat or  10mm each coat for multiple layers. Press the first layer hard against the surface.

For the second layer, allow the first layer to set partially (60-120min depending on weather). Apply the second layer as described above.

Water spray the surface if the second layer is carried out the next day.


Cure Vetotouch Monocouche by spraying water evenly on the surfaces of applied materials every 12 hrs for a minimum of 3 days. During hot & dry conditions, allow curing for a minimum of 5-7 days; it will help obtain high mechanical strength.

To protect the final color look, it is recommended to apply one coat of Saveto Vetoseal product range (contact the technical department for advice).


Clean tools with water before the mortar hardens. After the hardening, remove its residuals mechanically only.

Surface Preparation

The substrate should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc.

Before Vetotouch Monocouche, wet the entire surfaces with clean potable water, and the surface should look damp at the time of Vetotouch Monocouche application.

  • Do not mix with any additives or products unless recommended by Saveto.
  • Make sure the substrate is suitable for plaster application. In case of doubt, try on sample area to assess its suitability.
  • Do not apply the product at a temperature less than +5ºC. During the summer season, the working area must be covered to prevent ill-effects from direct sun and excessive air-draught during the initial curing stage.
Additional Information
Health & Sefety

Vetotouch Monocouche is highly alkaline; therefore, avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be wash with soap & water. In case of eye irritation, immediately wash with a copious amount of cold water. Seek medical advice.

Vetotouch Monocouche is non-flammable.

For further information, please refer to the product material safety data sheet.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products because it has no direct or continuous control over where or how its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the technical datasheets' specifications upon its discretion without prior notification. 

Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Vetotouch Europa

Cementitious polymer modified decorative finish coat applied at thicknesses from 1 to 5mm

Vetotouch Graviatto

Grooved decorative finish coat

Vetotouch Marmo

Marble chip decorative exterior and interior finishing system

Vetotouch Serene

Cementitious polymer modified decorative finish coat applied at thicknesses from 1 to 3mm

Vetotouch Textura
Acrylic polymer modified decorative finish coat applied at thicknesses from 5 to 20mm


Acrylic polymer modified decorative finish coat applied at thicknesses from 5 to 20mm

view more
Featured Product
Vetotop UC363
High performance, aromatic & flexible waterproof polyurethane flooring membrane


High performance, aromatic & flexible waterproof polyurethane flooring membrane

Carpark decks.
Food and pharmaceutical industry flooring.
Aircraft hangers.
Service centers, workshops.
Connected products
Spatter Dash SB

Cementitious Scratch / Key Coat

Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com